PIC18LF6410-I/PT

MCU 8Bit PIC18 PIC RISC 16KB Flash 2.5V/3.3V/5V 64Pin TQFP Tray

PIC series IC 8 位 40MHz 16KB（8K x 16） 闪存 64-TQFP（10x10）

得捷:
IC MCU 8BIT 16KB FLASH 64TQFP

艾睿:
MCU 8-bit PIC18 PIC RISC 16KB Flash 2.5V/3.3V/5V 64-Pin TQFP Tray

Allied Electronics:
16 KB Flash, 768 RAM, 68 I/O64 TQFP 10x10x1mm TRAY

安富利:
PIC18LF6410 offers the advantages of all PIC18 microcontrollers – namely, high computational performance at an economical price. In addition to these features, the PIC18F6310/6410/8310/8410 family introduces design enhancements that make these microcontrollers a logical choice for many high-performance, power-sensitive applications.All of the devices in the PIC18F6310/6410/8310/8410 family incorporate a range of features that can significantly reduce power consumption during operation.Alternate Run Modes: By clocking the controller from the Timer1 source or the internal oscillator block, power consumption during code execution can be reduced by as much as 90%.Multiple Idle Modes: The controller can also run with its CPU core disabled, but the peripherals still active. In these states, power consumption can be reduced even further – to as little as 4% of normal operation requirements.On-the-Fly Mode Switching: The power-managed modes are invoked by user code during operation, allowing the user to incorporate power-saving ideas into their application’s software designLower Consumption in Key Modules: The power requirements for both Timer1 and the Watchdog Timer have been reduced by up to 80%, with typical values of 1.1 µA and 2.1 µA, respectively.All of the devices in the PIC18F6310/6410/8310/8410 family offer nine different oscillator options, allowing users a wide range of choices in developing application hardware.* Four Crystal modes, using crystals or ceramic resonators. * Two External Clock modes, offering the option of using two pins oscillator input and a divide-by-4 clock output or one pin oscillator input, with the second pin reassigned as general I/O. * Two External RC Oscillator modes, with the same pin options as the External Clock modes. * An internal oscillator block which provides an 8 MHz clock ±2% accuracy and an INTRC source approximately 31 kHz, stable over temperature and VDD, as well as a range of six user-selectable clock frequencies between 125 kHz to 4 MHz for a total of eight clock frequencies. This option frees the two oscillator pins for use as additional general purpose I/O. * A Phase Lock Loop PLL frequency multiplier, available to both the High-Speed Crystal and Internal Oscillator modes, which allows clock speeds of up to 40 MHz. Used with the internal oscillator, the PLL gives users a complete selection of clock speeds from 31 kHz to 32 MHz – all without using an external crystal or clock circuit.Besides its availability as a clock source, the internal oscillator block provides a stable reference source that gives the family additional features for robust operation:Fail-Safe Clock Monitor: This option constantly monitors the main clock source against a reference signal provided by the internal oscillator. If a clock failure occurs, the controller is switched to the internal oscillator block, allowing for continued low-speed operation or a safe application shutdown.Two-Speed Start-up: This option allows the internal oscillator to serve as the clock source from Power-on Reset or wake-up from Sleep mode until the primary clock source is available

Chip1Stop:
MCU 8-bit PIC18 PIC RISC 16KB Flash 2.5V/3.3V/5V 64-Pin TQFP Tray

Newark:
# MICROCHIP  PIC18LF6410-I/PT  8 Bit Microcontroller, Flash, PIC18LF6xxx, 40 MHz, 16 KB, 768 Byte, 64 Pins, TQFP

DeviceMart:
IC PIC MCU FLASH 8KX16 64TQFP

Win Source:
IC MCU 8BIT 16KB FLASH 64TQFP / PIC series Microcontroller IC 8-Bit 40MHz 16KB 8K x 16 FLASH 64-TQFP 10x10