LPC43S30FET256E
ARM微控制器 - MCU 32BIT ARM M4 256LBGA
Overview
The LPC43S30FET256 is a ARM Cortex-M4 based microcontroller for embedded applications which includes an ARM Cortex-M0 coprocessor, 264 kB of SRAM, security features with AES engine, advanced configurable peripherals such as the State Configurable Timer/PWM SCTimer/PWM and the Serial General-Purpose I/O SGPIO interface, two High-speed USB controllers, Ethernet, an external memory controller, and multiple digital and analog peripherals. The LPC43S30FET256 operates at CPU frequencies of up to 204 MHz.
The ARM Cortex-M4 is a 32-bit core that offers system enhancements such as low power consumption, enhanced debug features, and a high level of support block integration. The ARM Cortex-M4 CPU incorporates a 3-stage pipeline, uses a Harvard architecture with separate local instruction and data buses as well as a third bus for peripherals, and includes an internal prefetch unit that supports speculative branching. The ARM Cortex-M4 supports single-cycle digital signal processing and SIMD instructions. A hardware floating-point unit is integrated in the core.
The ARM Cortex-M0 coprocessor is an energy-efficient and easy-to-use 32-bit core which is code- and tool-compatible with the Cortex-M4 core. The Cortex-M0 coprocessor offers up to 204 MHz performance with a simple instruction set and reduced code size. In LPC43Sx0, the Cortex-M0 coprocessor hardware multiply is implemented as a 32-cycle iterative multiplier.
MoreLess
## Features
* Cortex-M4 Processor core
* ARM Cortex-M4 processor, running at frequencies of up to 204 MHz.
* Built-in Memory Protection Unit MPU supporting eight regions.
* Built-in Nested Vectored Interrupt Controller NVIC.
* Hardware floating-point unit making the core a Cortex-M4.
* Non-maskable Interrupt NMI input.
* JTAG and Serial Wire Debug SWD, serial trace, eight breakpoints, and four watch points.
* Enhanced Trace Module ETM and Enhanced Trace Buffer ETB support.
* System tick timer.
* Cortex-M0 Processor core
* ARM Cortex-M0 coprocessor capable of off-loading the main ARM Cortex-M4F application processor.
* Running at frequencies of up to 204 MHz.
* JTAG
* Built-in NVIC.
* On-chip memory
* 264 kB SRAM for code and data use.
* Multiple SRAM blocks with separate bus access. Two SRAM blocks can be powered down individually
* 64 kB ROM containing boot code and on-chip software drivers.
* 64 bit general-purpose OTP memory
* Two banks 256 bit total One-Time Programmable OTP memory for AES key storage One bank can store an encrypted key for decoding the boot image.
* AES engine for encryption and decryption of the boot image and data with DMA support and programmable via a ROM-based API.
* Clock generation unit
* Crystal oscillator with an operating range of 1 MHz to 25 MHz.
* 12 MHz Internal RC IRC oscillator trimmed to 1.5 % accuracy over temperature and voltage.
* Ultra-low power Real-Time Clock RTC crystal oscillator.
* Three PLLs allow CPU operation up to the maximum CPU rate without the need for a high-frequency crystal. The second PLL is dedicated to the High-speed USB, the third PLL can be used as audio PLL.
* Clock output.
* Configurable digital peripherals
* Serial GPIO SGPIO interface.
* State Configurable Timer SCTimer/PWM subsystem on AHB.
* Global Input Multiplexer Array GIMA allows to cross-connect multiple inputs and outputs to event driven peripherals like the timers, SCTimer/PWM, and ADC0/1.
* Serial interfaces
* Quad SPI Flash Interface SPIFI with 1-, 2-, or 4-bit data at rates of up to 52 MB per second.
* 10/100T Ethernet MAC with RMII and MII interfaces and DMA support for high throughput at low CPU load. Support for IEEE 1588 time stamping/advanced time stamping IEEE 1588-2008 v2.
* One High-speed USB 2.0 Host/Device/OTG interface with DMA support and on-chip high-speed PHY USB0.
* One High-speed USB 2.0 Host/Device interface with DMA support, on-chip full-speed PHY and ULPI interface to external high-speed PHY USB1.
* USB interface electrical test software included in ROM USB stack.
* Four 550 UARTs with DMA support: one UART with full modem interface; one UART with IrDA interface; three USARTs support UART synchronous mode and a smart card interface conforming to ISO7816 specification.
* Up to two C_CAN 2.0B controllers with one channel each. Use of C_CAN controller excludes operation of all other peripherals connected to the same bus bridge
* Two SSP controllers with FIFO and multi-protocol support. Both SSPs with DMA support.
* One SPI controller.
* One Fast-mode Plus I²C-bus interface with monitor mode and with open-drain I/O pins conforming to the full I²C-bus specification. Supports data rates of up to 1 Mbit/s.
* One standard I²C-bus interface with monitor mode and with standard I/O pins.
* Two I²S interfaces, each with DMA support and with one input and one output.
* Digital peripherals
* External Memory Controller EMC supporting external SRAM, ROM, NOR flash, and SDRAM devices.
* Secure Digital Input Output SD/MMC card interface.
* Eight-channel General-Purpose DMA controller can access all memories on the AHB and all DMA-capable AHB slaves.
* Up to 164 General-Purpose Input/Output GPIO pins with configurable pull-up/pull-down resistors.
* GPIO registers are located on the AHB for fast access. GPIO ports have DMA support.
* Up to eight GPIO pins can be selected from all GPIO pins as edge and level sensitive interrupt sources.
* Two GPIO group interrupt modules enable an interrupt based on a programmable pattern of input states of a group of GPIO pins.
* Four general-purpose timer/counters with capture and match capabilities.
* One motor control Pulse Width Modulator PWM for three-phase motor control.
* One Quadrature Encoder Interface QEI.
* Repetitive Interrupt timer RI timer.
* Windowed watchdog timer WWDT.
* Ultra-low power Real-Time Clock RTC on separate power domain with 256 bytes of battery powered backup registers.
* Alarm timer; can be battery powered.
* Analog peripherals
* One 10-bit DAC with DMA support and a data conversion rate of 400 kSamples/s.
* Two 10-bit ADCs with DMA support and a data conversion rate of 400 kSamples/s. Up to eight input channels per ADC.
* Unique ID for each device.
* Power
* Single 3.3 V 2.2 V to 3.6 V power supply with on-chip internal voltage regulator for the core supply and the RTC power domain.
* RTC power domain can be powered separately by a 3 V battery supply.
* Four reduced power modes: Sleep, Deep-sleep, Power-down, and Deep power-down.
* Processor wake-up from Sleep mode via wake-up interrupts from various peripherals.
* Wake-up from Deep-sleep, Power-down, and Deep power-down modes via external interrupts and interrupts generated by battery powered blocks in the RTC power domain.
* Brownout detect with four separate thresholds for interrupt and forced reset.
* Power-On Reset POR.
* Available as LBGA256 package.
## Target Applications
* Communication hubs
* Automotive aftermarket
* Power management
* Consumer health devices
* Embedded audio applications
* Industrial control
* Industrial automation
* White goods
## Features
