锐单电子商城 , 一站式电子元器件采购平台!
  • 电话:400-990-0325

PD快充3.0协议芯片

时间:2023-06-10 07:37:00 pd57006集成电路

PD快充3.0协议芯片RK837,PD支持快速充电协议芯片USBPD3.0协议芯片

市场上有越来越多的快速充电设备,包括华为、三星、小米、诺基亚、锤子、索尼、魅族、雷蛇等主流品牌手机PD手机充电配置中包含了快速充电协议。

后续会有更多的品牌手机支持PD快充,PD快速充大统一无疑是行业趋势。

介绍瑞芯微推出的瑞芯微RK837PD快充3.0协议芯片

RK837PD快充3.0协议芯片功能介绍

可支持5V、9V、12V、15V、20V等多档电压,

支持一个USB Type-C端口和一个Type-A港口

支持USB PD 3.0,C型PHY和协议,PD TID号是5141

支持QC4 协议,报告号为QC20210303222

集成BMC收发器和PHYMCU MCU其他专有协议支持

集成Cortex-M0、64K和2K字节RAM

DP / DM可配置引脚UART模式,BC1.2模式和GPIO模式

DP2 / DM可配置2引脚BC1.2模式和GPIO模式CC CCCV控制器

3?22V,10mV / step(11bits)CV输出

0.1A?12A,步进12mA(5mohm Rsense)?高精度ADCtes集成10通道电压ADC

1通道电流ADC

其它功能和保护

集成了N-MOSFET输出控制驱动器tes集成了快速放电的集成N-MOSFET

集成了VBUS放电电路

低功耗集成RC振荡器,3定时器/ PWM和WDT

保护:OCP,OVP,UVP,OTP

FN QFN-24 4x4mm封装

RK837是USB PD3.0 Type C适配器采用控制器,支持一个USB Type-C端口和A型端口。它集成了Cortex-M0,闪存和RAM来处理PD协议、战略引擎和设备战略管理器。 它的内置BMC用于USB PD通信。次级侧CC和CV更换环路调节内置放大器TL431。 高增益、高精度电流检测放大器,在感测电阻器中降低功耗。 一个10位DAC调整CC和一个11位DAC调整CV。

RK837还集成了PD3.0协议适配器。M0内核,64K字节闪存空间,2K字节RAM实现PD3.0或其他协议。 C型PHY和BMCPHY还集成在RK837中。借助高精度ADC,不仅可以持续监测电压、电流、温度等系统参数,还可以通过PD3.0协议与手机进行通讯各种需求。所有GPIO均可配置为ADC触发输入或边缘中断。 可以将DP / DM引脚配置为UART模式和BC1.2模式。 它支持I2C接口。RK837集成了输出开关N-MOSFET 集成了VCC和VBUS放电功能PD要求。

RK837 is a USB PD3.0 Type C controller for adapters, supporting one USB Type-C port and one Type A port. It integrates Cortex-M0, flash memory and RAM to handle PD protocol, policy engine and device policy manager. Its built-in BMC is used for USB PD communication. The CC and CV loop adjustment on the secondary side have built-in amplifiers instead of TL431. The high gain and high precision current sense amplifier reduces power consumption in the sense resistor. A 10-bit DAC adjusts CC and an 11-bit DAC adjusts CV.

RK837 also integrates PD3.0 protocol adapter. M0 core, 64K bytes of flash memory space, 2K bytes of RAM to implement PD3.0 or other protocols. Type C PHY and BMCPHY are also integrated in RK837. With the help of a high-precision ADC, not only can you continuously monitor system parameters such as voltage, current, and temperature, but you can also communicate with the mobile phone through the PD3.0 protocol for various needs. All GPIOs can be configured as ADC inputs or edge-triggered interrupts. The DP/DM pins can be configured as UART mode and BC1.2 mode. It supports I2C interface. RK837 integrates an output switch N-MOSFET and integrates VCC and VBUS discharge function PD requirements.

锐单商城拥有海量元器件数据手册IC替代型号,打造电子元器件IC百科大全!

相关文章