硬件工程师学习英语必备
时间:2022-07-04 12:00:00
- 1 -
英语电子专业词汇(硬件工程师必须学习英语)
1 backplane 背板
2 Band gap voltage reference 带隙电压参考
3 bench top supply 工作台电源
4 Block Diagram 方块图
5 Bode Plot 波特图
6 Bootstrap 自举
7 Bottom FET Bottom FET
8 bucket capacitor 桶形电容
9 chassis 机架
10 Combi-sense Combi-sense
11 constant current source 恒流源
12 Core Saturation 铁芯饱和
13 crossover frequency 交叉频率
14 current ripple 纹波电流
15 Cycle by Cycle 逐周期
16 cycle skipping 周期跳步
17 Dead Time 死区时间
18 DIE Temperature 核心温度
19 Disable 不使用,无效,禁用,关闭
20 dominant pole 主极点
21 Enable 使能,有效,启用
22 ESD Rating ESD 额定值
23 Evaluation Board 评估板
24 Exceeding the specifications below may
result in permanent damage to the device,or
device malfunction. Operation outside of the
parameters specified in the Electrical
Characteristics section is not implied. 超过下
表面规格的使用可能会对设备造成永久损坏或设置
故障准备。建议不要在电特性表中工作
数范围以外。
25 Failing edge 下降沿
26 figure of merit 品质因数
27 float charge voltage 浮充电压
28 flyback power stage 反驰功率级
29 forward voltage drop 前向压降
30 free-running 自由运行
31 Freewheel diode 继流二极管
32 Full load 满负载
33 gate drive 栅极驱动
34 gate drive stage 栅极驱动级
35 gerber plot Gerber 图
36 ground plane 接地层
37 Henry 电感单位:亨利
38 Human Body Model 人体模式
39 Hysteresis 滞回
40 inrush current 涌入电流
41 Inverting 反相
42 jittery 抖动
43 Junction 结点
44 Kelvin connection 开尔文连接
45 Lead Frame 引脚框架
46 Lead Free 无铅
47 level-shift 电平移动
48 Line regulation 电源调节率
49 load regulation 负载调整率
50 Lot Number 批号
51 Low Dropout 低压差
52 Miller 密勒
53 node 节点
54 Non-Inverting 非反相
55 novel 新颖的
56 off state 关断状态
57 Operating supply voltage 电源工作电压
58 out drive stage 输出驱动级
59 Out of Phase 异相
60 Part Number 产品型号
61 pass transistor pass transistor
62 P-channel MOSFET P 沟道 MOSFET
63 Phase margin 相位裕度
64 Phase Node 开关节点
65 portable electronics 便携式电子设备
66 power down 掉电
67 Power Good 电源正常
68 Power Groud 功率地
69 Power Save Mode 节电模式
70 Power up 上电
71 pull down 下拉
72 pull up 上拉
73 Pulse by Pulse 逐脉冲(Pulse by Pulse)
74 push pull converter 推拉转换器
75 ramp down 斜降
76 ramp up 斜升
77 redundant diode 冗余二极管
78 resistive divider 电阻分压器 - 2 -
79 ringing 振 铃
80 ripple current 纹波电流
81 rising edge 上升沿
82 sense resistor 检测电阻
83 Sequenced Power Supplys 序列电源
84 shoot-through 直通,同时导通
85 stray inductances. 杂散电感
86 sub-circuit 子电路
87 substrate 基板
88 Telecom 电信
89 Thermal Information 热性能信息
90 thermal slug 散热片
91 Threshold 阈值
92 timing resistor 振荡电阻
93 Top FET Top FET
94 Trace 线路,线路,引线
95 Transfer function 传递函数
96 Trip Point 跳变点
97 turns ratio 匝数比,=Np / Ns。(初级匝
数/次级匝数)
98 Under Voltage Lock Out (UVLO) 欠压锁
定
99 Voltage Reference 电压参考
100 voltage-second product 伏秒积
101 zero-pole frequency compensation 零极点
频率补偿
102 beat frequency 拍频
103 one shots 单击电路
104 scaling 缩放
105 ESR 等效串联电阻
106 Ground 地电位
107 trimmed bandgap 平衡带隙
108 dropout voltage 压差
109 large bulk capacitance 大容量电容
110 circuit breaker 断路器
111 charge pump 电荷泵
112 overshoot 过冲
1) 元件设备
三绕组 变 器:three-column transformer
ThrClnTrans
双绕组变压器:double-column transformer
DblClmnTrans
电容器:Capacitor
并联电容器:shunt capacitor
电抗器:Reactor
母线:Busbar
输电线:TransmissionLine
发电厂:power plant
断路器:Breaker
刀闸(隔离开关):Isolator
分接头:tap
电动机:motor
(2) 状态参数
有功:active power
无功:reactive power
电流:current
容量:capacity
电压:voltage
档位:tap position
有功损失:reactive loss
无功损失:active loss
功率因数:power-factor
功率:power
功角:power-angle
电压等级:voltage grade
空载损耗:no-load loss
铁损:iron loss
铜损:copper loss
空载电流:no-load current
阻抗:impedance
正序阻抗:positive sequence impedance
负序阻抗:negative sequence impedance
零序阻抗:zero sequence impedance
电阻:resistor
电抗:reactance
电导:conductance
电纳:susceptance
无功负载:reactive load 或者 QLoad
有功负载: active load PLoad
遥测:YC(telemetering)
遥信:YX
励磁电流(转子电流):magnetizing current
定子:stator
功角:power-angle
上限:upper limit
下限:lower limit
并列的:apposable
高压: high voltage
低压:low voltage - 3 -
中压:middle voltage
电力系统 power system
发电机 generator
励磁 excitation
励磁器 excitor
电压 voltage
电流 current
母线 bus
变压器 transformer
升压变压器 step-up transformer
高压侧 high side
输电系统 power transmission system
输电线 transmission line
固定串联电容补偿 fixed series capacitor
compensation
稳定 stability
电压稳定 voltage stability
功角稳定 angle stability
暂态稳定 transient stability
电厂 power plant
能量输送 power transfer
交流 AC
装机容量 installed capacity
电网 power system
落点 drop point
开关站 switch station
双回同杆并架 double-circuit lines on the
same tower
变电站 transformer substation
补偿度 degree of compensation
高抗 high voltage shunt reactor
无功补偿 reactive power compensation
故障 fault
调节 regulation
裕度 magin
三相故障 three phase fault
故障切除时间 fault clearing time
极限切除时间 critical clearing time
切机 generator triping
高顶值 high limited value
强行励磁 reinforced excitation
线路补偿器 LDC(line drop compensation)
机端 generator terminal
静态 static (state)
动态 dynamic (state)
单机无穷大系统 one machine - infinity bus
system
机端电压控制 AVR
电抗 reactance
电阻 resistance
功角 power angle
有功(功率) active power
无功(功率) reactive power
功率因数 power factor
无功电流 reactive current
下降特性 droop characteristics
斜率 slope
额定 rating
变比 ratio
参考值 reference value
电压互感器 PT
分接头 tap
下降率 droop rate
仿真分析 simulation analysis
传递函数 transfer function
框图 block diagram
受端 receive-side
裕度 margin
同步 synchronization
失去同步 loss of synchronization
阻尼 damping
摇摆 swing
保护断路器 circuit breaker
电阻:resistance
电抗:reactance
阻抗:impedance
电导:conductance
电纳:susceptance
导纳:admittance
电感:inductance
电容: capacitance
coupling 耦合 intermittent 周 期 的
dislocation 错位
propeller 螺 旋 桨 switchgear 配 电 装 置
dispersion 差量
flange 法兰盘 dielectric 介电的 binder 胶
合剂
alignment 定 位 elastomer 合 成 橡 胶
corollary 必然的结果 - 4 -
rabbet 插槽 vent 通风孔 subtle 敏感的
gearbox 变速箱 plate 电镀 crucial 决定性
的
flexible 柔性的 technics 工艺 ultimate 最终
的
resilience 弹性 vendor 自动售货机 partition
分类
rigid 刚性的 prototype 样机 diagram 特性
曲线
interfere 干涉 compatible 兼容的 simulation
模拟
clutch 离合器 refinement 精加工 fixture 夹
具
torque 扭矩 responsive 敏感的 tensile 拉伸
cushion 减震器 rib 肋 strength 强度
packing 包装 metallized 金属化 stress 应力
mitigate 减轻 trade off 折衷方案 yield 屈
伸
line shaft 中间轴 matrix 母体 inherent 固有
的
spindle 主轴 aperture 孔径 conformance 适
应性
axle 心轴 turbulence 扰动 specification 规
范
semipermanent 半永久性的 enclosure 机壳
specialization 规范化
bolt 螺栓 oscillation 振幅 calling 职业
nut 螺母 anneal 退火 vitalize 激发
screw 螺丝 polymer 聚合体 revelation 揭
示
fastner 紧固件 bind 凝固 dissemination 分
发
rivit 铆钉 mount 支架 booster 推进器
hub 轴套 distortion 变形 contractual 契约
的
coaxial 同心的 module 模块 verdict 裁决
crank 曲柄 slide 滑块 malfunction 故障
inertia 惰性 medium 介质 allegedly 假定
active 活性的 dissipation 损耗 controversy
辩论
lubrication 润滑 assembly 总装 dictate 支
配
graphite 石墨 encapsulate 封装 incumbent
义不容辞的
derivative 派 生 物 adhesive 粘 合 剂
validation 使生效
contaminate 沾染 turbine 涡轮 procurement
收购
asperity 粗糙 bearing 支撑架 mortality 失
败率
metalworking 金属加 工 isostatic 均 衡 的
shed light on 阐明
viscous 粘稠的 osculate 接触 adversely 有
害的
grinding 研 磨 imperative 强 制 的
consistency 连续性
corrosin 侵蚀 lattice 晶格 fitness 适应性
flush 冲洗 fracture 断裂 warrant 保证
inhibitor 防腐剂 diffusivity 扩散率 turning
车工
dispersant 分 散 剂 vice versa 反 之 亦 然
ways 导轨
deteriorate 降低 tribological 摩擦的 hybrid
混合物
neutralize 平 衡 screen 屏 蔽 ID=inside
diameter
pulley 滑 轮 exclusion 隔 绝 OD=outside
diameter
hydraulic 液 压 的 insulation 绝 缘
reciprocate 往复运动
delicate 精密的 elaborate 加工 dress 精整
dampen 阻尼 incontrovertible 无可争议的
by and large 大体上
pivotal 中枢的 luminous 发光的 plastic 塑
胶
utilitarian 功 利 主 义 out of round 失 园
organic 有机的
grass root 基层 premature 过早的 film 薄
膜
state-of-the -art 技术发展水平 guard 防护罩
polyester 聚酯
blade 托板 permeate 渗入 epoxy 环氧的
carrier 载体 spillage 溢出 polypropylene 聚
丙烯
chuck 卡盘 erosion 浸蚀 photoconductive
光敏的
infeed 横 向 进 给 routine 程 序
miniaturization 小型化
lapping 抛 光 postprocess 后 置 处 理 - 5 -
asynchronism 异步
milling 洗 削 solder-bump 焊 点
synchronization 同步
speciality 专业 grid 栅格 respond 响应
stroke 行程 impedance 阻抗 feedback 反馈
attachment 备 件 approximately 大 约
aberrance 畸变
tapered 楔形的 purported 据说 steady 稳态
的
casting 铸件 consumable 消费品 dynamic
动态的
index 换档 inductance 电感 transient 瞬态
的
stop 挡块 capacitance 电容 coordinate 坐标
contour 轮廓 resistance 电容 curve 曲线
machine center 加工中心 audion 三极管
diagram 特性曲线
capitalize 投资 diode 二极管 history 关系
曲线
potentiometer 电 位 器 transistor 晶 体 管
gradient 斜率
know-how 实 践 知 识 choker 扼 流 圈
parabola 抛物线
potted 封装的 filter 滤波器 root 根
mechatronics 机电一体化 transformer 变压
器 eigenvalue 特征值
stem from 起源于 fuse 保险丝 function 函
数
rule-based 基于规则的 annular core 磁环
vector 向量
consolidation 巩 固 radiator 散 热 器
reciprocal 倒数
energize 激发 regulator 稳压器 virtual value
有效值
synchronous 同时发生 bobbin 骨架 square
root 平方根
socket 插孔 tape 胶带 cube 立方
polarity 极性 ceramic capacitor 瓷片电容
integral 积分
armature 电 枢 electrolytic C 电 解 电 容
differential 微分
installment 分期付款 self-tapping screw 自
攻螺丝 hisgram 直方图
lobe 凸起 footprint 封装 ratio 比率
plunge 钻入 resin 松香 grade down 成比例
降低
servo 伺 服 机 构 solderability 可 焊 性
proportion 比例
dedicated 专用的 shock 机械冲击 inverse
ratio 反比
interpolation 插补 endurance 耐久性 direct
ratio 正比
compensation 校正 initial value 初始值 plus
加
upload 加载 flashing 飞弧 subtract 减
overload 过载 canned 千篇一律的 multiply
乘
lightload 轻载 lot 抽签 divide 除
stagger 交错排列 parallel 并联 impedance
阻抗
traverse 横向 in series 串联 damp 阻尼
longitudinal 纵 向 的 equivalent 等 效 的
reactance 电抗
latitudinal 横向的 terminal 终端 admittance
导纳
restrain 约束 creep 蠕动 susceptance 电纳
square 平方
Hyperlink 超级连接 spring 触发
memo 备忘录 wastage 损耗
presentation 陈述 principle 原理
binder 打包 planer 刨床
source program 源程序
Client-Server Model 客户机
server 服务器
table 表
query 查询
form 表单
report 报表
macro 宏
module 模块
field 字段
record 记录
printed circuit 印制电路
printed wiring 印制线路
printed board 印制板
printed circuit board 印制板电路
printed wiring board 印制线路板
printed component 印制元件
printed contact 印制接点 - 6 -
printed board assembly 印制板装配
board 板
rigid printed board 刚性印制板
flexible printed circuit 挠性印制电路
flexible printed wiring 挠性印制线路
flush printed board 齐平印制板
metal core printed board 金属芯印制板
metal base printed board 金属基印制板
mulit-wiring printed board 多重布线印制板
molded circuit board 模塑电路板
discrete wiring board 散线印制板
micro wire board 微线印制板
buile-up printed board 积层印制板
surface laminar circuit 表面层合电路板
B2it printed board 埋入凸块连印制板
chip on board 载芯片板
buried resistance board 埋电阻板
mother board 母板
daughter board 子板
backplane 背板
bare board 裸板
copper-invar-copper board 键盘板夹心板
dynamic flex board 动态挠性板
static flex board 静态挠性板
break-away planel 可断拼板
cable 电缆
flexible flat cable (FFC) 挠性扁平电缆
membrane switch 薄膜开关
hybrid circuit 混合电路
thick film 厚膜
thick film circuit 厚膜电路
thin film 薄膜
thin film hybrid circuit 薄膜混合电路
interconnection 互连
conductor trace line 导线
flush conductor 齐平导线
transmission line 传输线
crossover 跨交
edge-board contact 板边插头
stiffener 增强板
substrate 基底
real estate 基板面
conductor side 导线面
component side 元件面
solder side 焊接面
printing 印制
grid 网格
pattern 图形
conductive pattern 导电图形
non-conductive pattern 非导电图形
legend 字符
mark 标志
base material 基材
laminate 层压板
metal-clad bade material 覆金属箔基材
copper-clad laminate (CCL) 覆铜箔层压板
composite laminate 复合层压板
thin laminate 薄层压板
basis material 基体材料
prepreg 预浸材料
bonding sheet 粘结片
preimpregnated bonding sheer 预浸粘结片
epoxy glass substrate 环氧玻璃基板
mass lamination panel 预制内层覆箔板
core material 内层芯板
bonding layer 粘结层
film adhesive 粘结膜
unsupported adhesive film 无支撑胶粘剂膜
cover layer (cover lay) 覆盖层
stiffener material 增强板材
copper-c