CYBLE-012011-00

CYBLE-01201x-x0 EZ-BLE 蓝牙模块**CYBLE-01201x-x0** 模块包含将低功率蓝牙 BLE 无线连接添加到项目设计所需的所有必要组件。 它包括与蓝牙 4.1 标准版兼容的免版权使用费的 BLE 堆栈。 提供两种型号：一种完全认证和经认证的型号，一种未经认证的模块，无蔽罩，仅用于初始实验室开发。 PSoC Creator™ 提供用于配置、开发、编程和测试 BLE 应用的集成设计环境。CYBL10 48MHz Cortex-M0 核 PRoC，具有 128KB 闪存，16KB RAM 射频范围：2400 至 2482MHz ISM 频段 射频功率输出：高达 +3dBm 接收器灵敏度：-87dBm OTA 数据传输率：1Mbps 多达 23 个 GPIO 多达 22 个电容式传感器，用于按钮或滑块，具有液体容差 8 通道 12 位，1Msps ADC，带内部参考，采样和固定 S/H 及通道排序器 2 个串行通信块 SCB，可支持 I²C（主/从），SPI（主/从）或 UART 所有 GPIO（共用或段）上支持 LCD 驱动器 可编程低电压检测 LVD，从 +1.8 到 +4.5V 直流 I²S 主接口 印刷电路板天线 BLE 协议堆栈支持通用访问应用规范 GAP、中央、外围设备、观察器和广播器角色 在移动中可在中央和外围设备角色之间切换 标准 BLE 配置文件和服务 功率模式：有功、睡眠、深度睡眠、休眠和停止 电源：+1.8V 至 +5.5V 直流 工作温度范围：-40 至 +85°C 尺寸：14.52 x 19.20mm，SMT 格式 应用：物联网 IoT 的短程通信 **RS 产品代码** 124-4406 CYBLE-012011-00 PRoC EZ-BLE 无线电模块，完全认证 124-4407 CYBLE-012012-10 PRoC EZ-BLE 无线电模块，未经认证 ### 注提供评估板，RS 部件号 124-4197。### 认可CE、FCC、IC、MIC、KC（仅限 CYBLE-012011-00）### 蓝牙 - Cypress Semiconductor

The is an EZ-BLE PRoC module. This is a turnkey Bluetooth Low Energy BLE wireless module solution which includes onboard crystal oscillators, trace antenna, passive components and the Cypress PRoC BLE. The CYBLE-012011-00 includes FCC/IC/KC/MIC/CE RF certification and Bluetooth SIG qualification. It supports a number of peripheral functions ADC, timers, counters, PWM and serial communication protocols I2C, UART, SPI through its programmable architecture. It has 128KB of flash and 16KB of SRAM. It includes a royalty-free BLE stack compatible with Bluetooth 4.1 and provides up to 23 GPIOs in a 14.52mm x 19.2mm x 2mm package.

.

32bit processor 0.9DMIPS/MHz with single cycle 32bit multiply

.

Operating at up to 48MHz

.

Industrial temperature range from -40°C to +85°C

.

Two-pin SWD for programming

.

Watchdog timer with dedicated internal low-speed oscillator ILO

.

Four dedicated 16bit timer, counter or PWM blocks and I2S master interface

.

LCD drive supported on all GPIOs common or segment

.

Reprogrammable architecture, flexible communication protocol support

.

Easy to use integrated design environment to configure, develop, program & test a BLE application