MK63FN1M0VLQ12R

Kinetis K 32Bit MCU, ARM Cortex-M4 core, 1Mb Flash, 120MHz, Ethernet, QFP 144

Overview

The Kinetis® K63 120MHz family of MCUs targets applications requiring security encryption, tamper detection, large memory densities and low-power processing efficiency.

* Provides for precision clock synchronization for real-time industrial control

* Accommodates a wide range of requirements via a rich suite of analog, communication, timing and control peripherals

* Supports crystal-less USB design for reduced system cost and board space

* Offers industry-leading low power while providing significant BOM savings through smart on-chip integration

* Includes hardware encryption coprocessor for secure data transfer and storage

* Shares the Kinetis portfolio’s robust enablement and scalability

MoreLess

## Features

### Ultra-Low-Power

* Flexible low-power modes with power and clock gating for optimal peripheral activity and recovery times. Stop currents of <340 nA, run currents of <250 µA/MHz, 4.5 µs wake-up from Stop mode

* Full memory and analog operation down to 1.71 volts for extended battery life

* Low-leakage wake-up unit with up to seven internal modules and 16 pins as wake-up sources in low-leakage stop LLS/very low-leakage stop VLLS modes

* Low-power timer for continual system operation in reduced power state

### Flash and SRAM

* 1 MB flash. Fast access, high reliability with four-level security protection

* 256 KB of SRAM

### Mixed-Signal Capability

* Two high-speed, 16-bit analog-to-digital converters ADCs with configurable resolution. Single or differential output mode operation for improved noise rejection. 500 ns conversion time achievable with programmable delay block triggering

* Two 12-bit digital-to-analog converters DACs for analog waveform generation for audio applications

* Three high-speed comparators providing fast and accurate motor over-current protection by driving PWMs to a safe state

* Analog voltage reference provides an accurate reference to analog blocks, ADC and DAC, and replaces external voltage references to reduce system cost

### Performance

* Arm Cortex-M4 core + DSP. 120 MHz, single-cycle MAC, single instruction multiple data SIMD extensions, single precision floating point unit

* Up to 16-channel DMA for peripheral and memory servicing with reduced CPU loading and faster system throughput

* Cross bar switch enables concurrent multi-master bus accesses, increasing bus bandwidth

* Independent flash banks allow concurrent code execution and firmware updating with no performance degradation or complex coding routines

### Timing and Control

* Up to four FlexTimers with a total of 20 channels. Hardware dead-time insertion and quadrature decoding for motor control

* Carrier modulator timer for infrared waveform generation in remote control applications

* Four-channel 32-bit periodic interrupt timer provides time base for RTOS task scheduler or trigger source for ADC conversion and programmable delay block

### Human-Machine Interface HMI

* GPIO with pin interrupt support

### Connectivity and Communications

* IEEE 1588 Ethernet MAC with hardware time stamping provides precision clock synchronization for real-time industrial control

* USB 2.0 On-The-Go full-speed with USB transceiver. Intelligent design with embedded 48 MHz oscillator allowing for USB crystal-less system design. Device charge detect optimizes charging current/time for portable USB devices enabling longer battery life. Low-voltage regulator supplies up to 120 mA off chip at 3.3 volts to power external components from 5 volts input

* Up to six UARTs with IrDA support including one UART with ISO7816 smart card support. Variety of data size, format and transmission/reception settings supported for multiple industrial communication protocols

* Inter-IC Sound I2S serial interface for audio system interfacing

* CAN module for industrial network bridging

* Three DSPI and three I2C

### Reliability, Safety and Security

* Memory protection unit provides memory protection for all masters on the cross bar switch, increasing software reliability

* Cyclic redundancy check engine validates memory contents and communication data, increasing system reliability

* Independent-clocked COP guards against clock skew or code runaway for fail-safe applications such as the IEC 60730 safety standard for household appliances

* External watchdog monitor drives output pin to safe state external components if watchdog event occurs

* System security and tamper detect with secure real-time clock with independent battery supply. Secure key storage with internal/external tamper detect for unsecure flash, temperature, clock, and supply voltage variations and physical attack detection