LPC4330FET100Y

ARM微控制器 - MCU Dual-core Cortex-M4/M0, 264 kB SRAM, 2 HS USB with on-chip PHY, Ethernet, CAN, AES, SPIFI, SGPIO, SCT

Overview

The LPC4330FET100 is an ARM Cortex-M4 based digital signal controller with an ARM Cortex-M0 coprocessor designed for embedded applications requiring signal processing. The ARM Cortex-M4 core offers single-cycle Multiply-Accumulate and SIMD instructions and a hardware floating-point unit to support signal processing while the M0 coprocessor handles I/O and digital control processing. The LPC4330FET100 includes 264 kB of data memory, two High Speed USB 2.0 Host/OTG/Devices, advanced configurable peripherals such as the State Configurable Timer SCT, Serial General Purpose I/O SGPIO, and SPI Flash Interface SPIFI as well as Ethernet, an external memory controller and multiple digital and analog peripherals.

MoreLess

## Features

* ARM Cortex-M4 processor, running at frequencies of up to 204 MHz

* ARM Cortex-M4 built-in Memory Protection Unit MPU supporting eight regions

* ARM Cortex-M4 built-in Nested Vectored Interrupt Controller NVIC

* Hardware floating-point unit

* Non-maskable Interrupt NMI input

* JTAG and Serial Wire Debug SWD

* System tick timer

* ARM Cortex-M0 co-processor running at frequencies of up to 204 MHz

* 264 kB SRAM for code and data use

* Two 32 kB SRAM blocks with separate bus access

* 32 kB ROM containing boot code and on-chip software drivers

* 32 bit One-Time Programmable OTP memory for customer use

* Serial GPIO SGPIO interface

* State Configurable Timer SCT subsystem on AHB

* Quad SPI Flash Interface SPIFI with four lanes and up to 40 MB per second

* 10/100T Ethernet MAC with RMII and MII interfaces and DMA support

* One High-speed USB 2.0 Host/Device/OTG interface with DMA support

* One High-speed USB 2.0 Host/Device interface with DMA support

* One 550 UART with DMA support and full modem interface

* Three 550 USARTs with DMA and synchronous mode support

* One C_CAN 2.0B controller with one channel

* Two SSP controllers with FIFO and multi-protocol support

* One SPI controller

* One Fast-mode Plus I2C-bus interface with rates of up to 1 Mbit/s

* One Fast-mode I2C-bus interface

* Two I2S interfaces

* External Memory Controller EMC supporting external SRAM, ROM, flash, SDRAM

* Secure Digital Input Output SDIO card interface

* Eight-channel General-Purpose DMA GPDMA controller

* Up to 49 General-Purpose Input/Output GPIO pins

* Four general-purpose timer/counters with capture and match capabilities

* One motor control Pulse Width Modulator PWM for three-phase motor control

* One Quadrature Encoder Interface QEI

* Repetitive Interrupt timer RI timer

* Windowed watchdog timer WWDT

* Ultra-low power Real-Time Clock RTC on separate power domain

* Alarm timer; can be battery powered

* One 10-bit DAC with DMA support and a data conversion rate of 400 kSamples/s

* Two 10-bit ADCs with DMA support and a data conversion rate of 400 kSamples/s

* Two 128-bit secure OTP memories for AES key storage and customer use

* Crystal oscillator with an operating range of 1 MHz to 25 MHz

* 12 MHz Internal RC IRC oscillator trimmed to 1 % accuracy

* Ultra-low power Real-Time Clock RTC crystal oscillator

* Three PLLs allow CPU operation up to the maximum CPU rate

* Clock output

* Single 3.3 V 2.2 V to 3.6 V power supply with on-chip DC-to-DC converter

* RTC power domain can be powered separately by a 3 V battery supply

* Four reduced power modes

* Processor wake-up from Sleep mode via wake-up interrupts

* Brownout detect with four separate thresholds for interrupt and forced reset

* Power-On Reset POR

* see selection guide for features per type

## Target Applications

* Industrial

* Consumer

* White goods

* RFID readers

* e-Metering

## Features