AT32UC3L0128-D3HR

32位微控制器 - MCU UC3L-128KB FL 85C

Description

The Atmel® AVR® AT32UC3L0128/256 is a complete system-on-chip microcontroller based on the AVR32 UC RISC processor running at frequencies up to 50MHz. AVR32 UC is a high-performance 32-bit RISC microprocessor core, designed for cost-sensitive embedded applications, with particular emphasis on low power consumption, high code density, and high performance.

The processor implements a Memory Protection Unit MPU and a fast and flexible interrupt controller for supporting modern and real-time operating systems. The Secure Access Unit SAU is used together with the MPU to provide the required security and integrity.

Features

• High-performance, Low-power 32-bit Atmel® AVR® Microcontroller

   – Compact Single-cycle RISC Instruction Set Including DSP Instructions

   – Read-modify-write Instructions and Atomic Bit Manipulation

   – Performance

• Up to 64DMIPS Running at 50MHz from Flash 1 Flash Wait State

• Up to 36DMIPS Running at 25MHz from Flash 0 Flash Wait State

   – Memory Protection Unit MPU

• Secure Access Unit SAU providing User-defined Peripheral Protection

• picoPower® Technology for Ultra-low Power Consumption

• Multi-hierarchy Bus System

   – High-performance Data Transfers on Separate Buses for Increased Performance

   – 12 Peripheral DMA Channels Improve Speed for Peripheral Communication

• Internal High-speed Flash

   – 256Kbytes and 128Kbytes Versions

   – Single-cycle Access up to 25MHz

   – FlashVault Technology Allows Pre-programmed Secure Library Support for End User Applications

   – Prefetch Buffer Optimizing Instruction Execution at Maximum Speed

   – 100,000 Write Cycles, 15-year Data Retention Capability

   – Flash Security Locks and User-defined Configuration Area

• Internal High-speed SRAM, Single-cycle Access at Full Speed

   – 32Kbytes

• Interrupt Controller INTC

   – Autovectored Low-latency Interrupt Service with Programmable Priority

• External Interrupt Controller EIC

• Peripheral Event System for Direct Peripheral to Peripheral Communication

• System Functions

   – Power and Clock Manager

   – SleepWalking Power Saving Control

   – Internal System RC Oscillator RCSYS

   – 32 KHz Oscillator

   – Multipurpose Oscillator, Phase Locked Loop PLL, and Digital Frequency Locked Loop DFLL

• Windowed Watchdog Timer WDT

• Asynchronous Timer AST with Real-time Clock Capability

   – Counter or Calendar Mode Supported

• Frequency Meter FREQM for Accurate Measuring of Clock Frequency

• Six 16-bit Timer/Counter TC Channels

   – External Clock Inputs, PWM, Capture, and Various Counting Capabilities

• PWM Channels on All I/O Pins PWMA

   – 8-bit PWM with a Source Clock up to 150MHz

• Four Universal Synchronous/Asynchronous Receiver/Transmitters USART

   – Independent Baudrate Generator, Support for SPI

   – Support for Hardware Handshaking

• One Master/Slave Serial Peripheral Interface SPI with Chip Select Signals

   – Up to 15 SPI Slaves can be Addressed

• Two Master and Two Slave Two-wire Interfaces TWI, 400kbit/s I2C-compatible

• One 8-channel Analog-to-digital Converter ADC with up to 12 Bits Resolution

   – Internal Temperature Sensor

• Eight Analog Comparators AC with Optional Window Detection

• Capacitive Touch CAT Module

   – Hardware-assisted Atmel® AVR® QTouch® and Atmel® AVR® QMatrix Touch Acquisition

   – Supports QTouch and QMatrix Capture from Capacitive Touch Sensors

• QTouch Library Support

   – Capacitive Touch Buttons, Sliders, and Wheels

   – QTouch and QMatrix Acquisition

• On-chip Non-intrusive Debug System

   – Nexus Class 2+, Runtime Control, Non-intrusive Data and Program Trace

   – aWire Single-pin Programming Trace and Debug Interface Muxed with Reset Pin

   – NanoTrace Provides Trace Capabilities through JTAG or aWire Interface

• 48-pin TQFP/QFN/TLLGA 36 GPIO Pins

• Five High-drive I/O Pins

• Single 1.62-3.6 V Power Supply